Tag: why is bitrate bad

Free Download Mp4Gain

How to Achieve High-Quality Videos with Low Bandwidth

 

Megapixel surveillance cameras provide their users with more detailed images; however, these capabilities can affect the cost of the entire video surveillance project.

The amount of data that is transported and stored, in this case, increases significantly. Bandwidth requirements and increased capacity required significantly increase the total cost of an IP video surveillance system. The best way to reduce these costs is on the surveillance camera itself, and this can be achieved by reducing the bit rate.

The bit rate can be reduced, in particular, due to noise reduction. Noise is quite a damaging factor that leads to clogging of the encoding process. It leads directly to an increase in the bit rate.

Optimize bitrate to reduce streaming

Classic noise reduction systems are of two types. Spatial noise reduction techniques are applied within the frame to help reduce noise, while temporal noise reduction averages the pixels over multiple frames. These are very effective techniques for still images, but they can cause problems when there is movement. In the event that a temporary noise reduction is applied to a moving image, a ghost image may appear.

By combining spatial and temporal noise reduction with the ability to dynamically adjust them based on lighting levels and the detection of moving objects, we obtain images with low noise, maximum detail and low bit rate. The bit rate can be optimized by adjusting the amount of noise reduction based on the analysis of important moving objects in the surveillance camera’s field of view. When there is no movement, the bit rate is kept to a minimum. If an important object is detected, the bit rate increases, allowing you to capture as much detail as possible. The result is that the bandwidth requirements of the network remain low until something important happens in the frame.

Other ways to reduce the bit rate
For some megapixel surveillance cameras, the bit rate is limited by default. Constant bit rate is often used for this. The constant bit rate is kept at a fixed level. This can result in a constant high bit rate, and setting a low bit rate can result in poor image quality.

Free Download Mp4Gain


Mp4Gain Main Window


Mp4Gain Features


Free Download Mp4Gain

Bit rate in DVR. What is it and what does it affect?

In a conversation about digital video recording, the term bit rate will surely ring a bell. This is an important parameter that affects image quality. Including filming on a video recorder.

If you are afraid of foreign words, then the bit rate can be called the recording speed or the compression ratio in another way. Because that’s exactly what happens: the compression of the video stream. How? Let’s take a look.

After the light hits the matrix and the subsequent digitization of the image, a very dense stream of digital video signal is obtained at the output. Also, the higher the video recording resolution and frame rate, the bulkier this stream will be. You cannot write it directly to a memory card; It will fill up very quickly with huge video files and you may just not be able to cope with such a flow of information. This is why the original video stream is compressed to an acceptable bit rate. This parameter is just the output data rate. Basically it reflects the speed at which the video is written to the memory card.

Bit rate can be calculated in bits, kilobits, and megabits per second – (bit / s, bps, b / s), (kbps, kbit / s, kbps) (Mbps, Mbit / s, Mbps). Most of the time, in megabits. The bit rate of the recorded video can be checked on a computer with a video editor or through the file properties menu. By dividing the figure by 8, you can determine it roughly in megabytes per second; it will be more convenient to compare it with the speed of your memory card.

The bit rate indicator is dependent, as you might guess, on the processor and intelligently optimized hardware and software to process the video stream. If all the conditions are met, the video stream will be compressed with high quality and with minimal loss. Otherwise, the video will contain noise, blurry images, artifacts, and other nasty distortions.

The bit rate also affects the size of the file. For example, at a relatively low bit rate (less than 10 megabits per second) more clips can fit on the memory card and cheap low speed cards can be used, but the video quality and details will be low. At a higher bit rate (10-20 begabits per second and more), the image will be of higher quality and more detailed. But the file size will also increase, so you need a memory card of the appropriate size and speed (16GB and above, class 10).

Manufacturers rarely indicate the bitrate on the box, therefore it is almost impossible to find out this indicator before buying. However, sometimes on the packaging you can see promises, for example, “8 hours of video in maximum quality at 32 GB”. And in this case, the bit rate can be roughly calculated. The formula is not complicated:
We took 32 gigabytes and, using the school’s computer skills, we converted them to megabits by multiplying them by eight and by 1024. Then we divided the resulting number by the number of seconds in eight hours.
– (32x8x1024) / (8×3600) – We get the result of 9.1 megabits per second.

Let’s clarify that the result will be conditional. First, because the actual volume of any card is always less than indicated. Second, the promises in the box can be just promises. Therefore, before buying, it is better to carefully study the selected model, having learned the speed of writing in the reviews.
So what bit rate should I be aiming for?

Given the adequate quality of the filling of the recorder (matrix + processor + lens + software), according to our practice, let’s say that this indicator is in the region of 15-45 megabits per second. This bit rate allows you to get a fairly adequate video quality during the day. Again, only during the day, because night photography, as we all know, is still a weak point of many recorders due to insufficient lens aperture and small matrix pixel size.

Note that DATAKAM has currently reached the maximum bit rate for recorders: 45 megabits per second, but only when working with a card with a capacity of 32 gigabytes or more. Some companies, notably Datakam and BlackVUE, are implementing bit rate selection options in settings. We find this option controversial. In our opinion, all drivers are initially interested in the highest quality videos, and it is easier to set the maximum bit rate for the recorder right away and simply choose the right memory card in terms of speed and volume.

And the last thing: they are unlikely to increase the bitrate incessantly on DVRs.